1. I beg your pardon dynamic routing protocol was arisen to interconnect various Internet business providers?
2. I beg your pardon routing protocol is limited to smaller network implementations because it does no accommodate expansion for larger networks?
3. What two tasks do dynamic routing protocols perform? (Choose two.)
update and maintain routing tables*
propagate hold default gateways
assign IP addressing
4. As soon as would the be more beneficial to usage a dynamic routing protocol rather of static routing?
in an organization with a smaller sized network that is not intended to flourish in size
on a stub network that has actually a solitary exit point
in an organization where routers suffer from performance issues
on a network where there is a most topology changes*
5. Once would that be much more beneficial to usage static routing rather of dynamic routing protocols?
on a network where dynamic updates would pose a protection risk*
on a network the is meant to continually prosper in size
on a network that has a large amount of redundant paths
on a network that typically experiences connect failures
6. What is a purpose of the network command when configuring RIPv2 together the routing protocol?
It identifies the interfaces the belong come a stated network.*
It mentions the far network that can now it is in reached.
You are watching: What two tasks do dynamic routing protocols perform? (choose two.)
It instantly advertises the stated network come neighbor routers v a classful mask.
It populates the routing table through the network entry.
7. A network administrator configures a static path on the sheet router that a network to entrust a gateway of critical resort. Exactly how would a network administrator configure the edge router to instantly share this route within RIP?
Use the auto-summary command.
Use the passive-interface command.
Use the network command.
Use the default-information originate command.*
8. What is the function of the passive-interface command?
allows a routing protocol to front updates the end an interface that is missing its IP address
allows a router to send routing to update on an interface but not get updates via that interface
allows an user interface to continue to be up there is no receiving keepalives
allows interfaces to share IP addresses
allows a router to get routing to update on an interface however not send to update via that interface*
9. Which path would be immediately created as soon as a router interface is activated and also configured v an IP address?
D 10.16.0.0/24 <90/3256> via 192.168.6.9
C 192.168.0.0/24 is straight connected, FastEthernet 0/0*
S 192.168.1.0/24 is directly connected, FastEthernet 0/1
O 172.16.0.0/16 <110/65> via 192.168.5.1
10. Refer to the exhibit. I m sorry two varieties of routes can be offered to describe the 192.168.200.0/30 route? (Choose two.)
level 1 parent route
level 1 network route
level 2 kid route*
11. What occurs next in the router lookup procedure after a router identify a location IP deal with and locates a equivalent level 1 parental route?
The level 2 child routes are examined.*
The level 1 supernet courses are examined.
The level 1 ultimate routes are examined.
The router fall the packet.
12. Which route would be offered to forward a packet through a source IP resolve of 192.168.10.1 and also a location IP deal with of 10.1.1.1?
C 192.168.10.0/30 is directly connected, GigabitEthernet0/1
S 10.1.0.0/16 is straight connected, GigabitEthernet0/0
O 10.1.1.0/24 <110/65> via 192.168.200.2, 00:01:20, Serial0/1/0*
S* 0.0.0.0/0 <1/0> via 172.16.1.1
13. Which two requirements are provided to recognize if a route deserve to be taken into consideration as one ultimate route in a router’s routing table? (Choose two.)
be a default route
contain an exit interface*
be a classful network entry
contain a next-hop IP address*
14. What is a disadvantage of utilizing dynamic routing protocols?
They space only suitable for straightforward topologies.
Their configuration complexity increases as the size of the network grows.
They send messages around network standing insecurely across networks by default.*
They call for administrator treatment when the pathway of traffic changes.
15. Which 2 statements are true about classless routing protocols? (Choose two.)
sends subnet mask information in routing updates*
sends complete routing table update to every neighbors
is supported by RIP variation 1
allows for use of both 192.168.1.0/30 and also 192.168.1.16/28 subnets in the same topology*
reduces the lot of address room available in one organization
16. Describe the exhibit. Based on the partial calculation from the display ip route command, what two facts have the right to be determined around the RIP routing protocol? (Choose two.)
RIP version 2 is to run on this router and also its RIP neighbor.*
The metric to the network 172.16.0.0 is 120.
RIP variation 1 is running on this router and its RIP neighbor.
The command no auto-summary has been used on the RIP neighborhood router.*
RIP will certainly advertise two networks to its neighbor.
17. If configuring RIPv2 ~ above an enterprise network, an technician enters the command network 192.168.10.0 right into router construction mode.
What is the result of entering this command?
The user interface of the 192.168.10.0 network is sending out version 1 and version 2 updates.
The interface of the 192.168.10.0 network is receiving variation 1 and also version 2 updates.
The interface of the 192.168.10.0 network is sending just version 2 updates.*
The user interface of the 192.168.10.0 network is sending out RIP hello messages.
18. A location route in the routing table is indicated with a code D. Which kind of route entry is this?
a static route
a route used as the default gateway
a network directly linked to a router interface
a course dynamically learned v the EIGRP routing protocol*
19. Refer to the exhibit. Which user interface will it is in the exit interface to front a data packet v the destination IP attend to 172.16.0.66?
20. Which kind of route will need a router to execute a recursive lookup?
an ultimate path that is making use of a next hop IP deal with on a router that is not making use of CEF*
a level 2 child path that is making use of an departure interface on a router the is not making use of CEF
a level 1 network course that is utilizing a following hop IP resolve on a router the is using CEF
a parent route on a router the is using CEF
21. Which route is the finest match because that a packet beginning a router with a destination address of 10.16.0.2?
S 10.0.0.0/8 <1/0> via 192.168.0.2
S 10.16.0.0/24 <1/0> via 192.168.0.9*
S 10.16.0.0/16 is straight connected, Ethernet 0/1
S 10.0.0.0/16 is straight connected, Ethernet 0/0
22. A router is configured to take part in many routing protocol: RIP, EIGRP, and OSPF. The router should send a packet come network 192.168.14.0. Which path will be supplied to front the traffic?
a 192.168.14.0/26 path that is learned via RIP*
a 192.168.14.0/24 route that is learned via EIGRP
a 192.168.14.0/25 path that is learned via OSPF
a 192.168.14.0/25 route that is learned via RIP
23. What is different between IPv6 routing table entries compared to IPv4 routing table entries?
IPv6 routing tables include local course entries i m sorry IPv4 routing tables perform not.
By design IPv6 is classless therefore all routes are effectively level 1 ultimate routes.*
The choice of IPv6 paths is based on the shortest corresponding prefix, unequal IPv4 route selection which is based on the longest corresponding prefix.
See more: Cute Couples Kissing Pics - Young Couple Kissing Stock Photos
IPv6 walk not use static routes to populate the routing table as offered in IPv4.
24. Match the dynamic routing protocol ingredient to the characteristic. (Not all alternatives are used.)
data structurestables or databases that room stored in RAM
routing protocol messagesexchanges routing information and also maintains accurate information around networks
algorithma finite list of actions used to determine the best path
25. Match the characteristic come the corresponding form of routing. (Not all alternatives are used.)
Place the choices in the adhering to order: <+> typically used ~ above stub networks <+> much less routing overhead <#> new networks are included automatically to the routing table <#> best choice for big networks